|
|
|
#2
01-21-2013, 05:30 PM
|
||||
|
||||
Thanks bear. I'm scared of the Spiderbox. Everyone talking about fabbing new front ends and all that. I can do mechanical and bolt ons all day long, but I have no tools or means to fabricate. I like the looks of the Trailmaster if I ever get another. I got my buggy up to 42mph today. WOO HOO
__________________
MXR TrailBender 160R SYC Perf head P&P,Matched intake and exhaust, A12 cam, Orange CDI & coil, Motorio pulley, 115mm Variator and lightweight drive face,11gm Sliders, UNI, modded muffler + 200 horsepower  http://www.youtube.com/watch?v=3hx-hEWl10c I'll take your insults as compliments and blame it on your lack of intelligence. |
|
#4
01-22-2013, 07:38 AM
|
||||
|
||||
|
Depending on where it comes from it can go by the name Spider 160r. Kandy makes a 250cc version with independant rear suspension. Oh....and a 250cc. I might go that route one day.
http://www.killermotorsports.com/mob...ult.aspx#P9389 High dollar though. But I like the sound of 14hp and 13# of torque.
__________________
MXR TrailBender 160R SYC Perf head P&P,Matched intake and exhaust, A12 cam, Orange CDI & coil, Motorio pulley, 115mm Variator and lightweight drive face,11gm Sliders, UNI, modded muffler + 200 horsepower http://www.youtube.com/watch?v=3hx-hEWl10c I'll take your insults as compliments and blame it on your lack of intelligence. |
|
#6
01-22-2013, 07:48 PM
|
||||
|
||||
|
I have about a 12" ground clearance. If you can find the Kandi version it looks like the frame and suspension is built a bit stronger. Kandi KD-150GKA2
__________________
MXR TrailBender 160R SYC Perf head P&P,Matched intake and exhaust, A12 cam, Orange CDI & coil, Motorio pulley, 115mm Variator and lightweight drive face,11gm Sliders, UNI, modded muffler + 200 horsepower http://www.youtube.com/watch?v=3hx-hEWl10c I'll take your insults as compliments and blame it on your lack of intelligence. Last edited by SLESTAK75; 01-22-2013 at 07:57 PM. |
|
#8
01-23-2013, 07:56 AM
|
||||
|
||||
|
it is a BIG buggy. Thus the deception in the pic. When I first built it the front wheels were toed out and it turned really wide unless you were moving along more that 5mph or so and then it turned really nice. I have since tried to adjust the toe ( I think they are closer to straight now) and it turns wide no matter what speed. I'm going to try toed in a bit and see how that does. It seems to have the potential to turn very nicely if properly set up. I've been trying to figure out the "proper" setup. Any suggestions??
__________________
MXR TrailBender 160R SYC Perf head P&P,Matched intake and exhaust, A12 cam, Orange CDI & coil, Motorio pulley, 115mm Variator and lightweight drive face,11gm Sliders, UNI, modded muffler + 200 horsepower http://www.youtube.com/watch?v=3hx-hEWl10c I'll take your insults as compliments and blame it on your lack of intelligence. |
|
#10
01-24-2013, 07:12 AM
|
||||
|
||||
|
Thats just about what ive been doing. I adjusted the toe in yesterday and bled a brake caliper that wasnt working and thats about all I could do. It finally got cold here in VA. In the 20s this morning getting down to teens tonight. Brrrrrr.
__________________
MXR TrailBender 160R SYC Perf head P&P,Matched intake and exhaust, A12 cam, Orange CDI & coil, Motorio pulley, 115mm Variator and lightweight drive face,11gm Sliders, UNI, modded muffler + 200 horsepower http://www.youtube.com/watch?v=3hx-hEWl10c I'll take your insults as compliments and blame it on your lack of intelligence. |
|
|
