|
150cc GY6 and Under Engine Tech GY6 and Smaller Technical Discussion Forum |
|
Thread Tools |
#1
|
|||
|
|||
Hammerhead hesitation
So lately I have been noticing that my buggy bogs down when the gas is initially depressed. It hesitates then takes off and on moderate hills that I used to fly up, it feels like it is struggling to maintain RPM's. Anyone have some input where to begin troubleshooting?
|
#2
|
|||
|
|||
May be running too rich in the warm weather. Mine acts like that when i take it to the trails about 1000 feet higher in elevation and dont rejet it to a smaller jet size.
__________________
Trailmaster XRX 150 TK Variator and 1500 Spring SYC Performance Ported & Polished & Shaved 2 Valve Head, A-10 Camshaft, R2C Filter, and Hammerhead Exhaust Hammerhead 250GTS White Torque and Clutch Springs, 18g Rollers, R2C Filter, Ported Polished and Shaved Head, Hammerhead Exhaust |
#3
|
||||
|
||||
There are three stages in these cv carbs we have on these buggies. That bog in the middle is usually caused by the 2nd stage. A google search for cv carb tuning will yeild some good artcles on this.
__________________
MXR TrailBender 160R SYC Perf head P&P,Matched intake and exhaust, A12 cam, Orange CDI & coil, Motorio pulley, 115mm Variator and lightweight drive face,11gm Sliders, UNI, modded muffler + 200 horsepower http://www.youtube.com/watch?v=3hx-hEWl10c I'll take your insults as compliments and blame it on your lack of intelligence. |
#4
|
|||
|
|||
I did some searching and from what I have read and like mb1134 said, I should rejet due to the warmer weather right?
|
#5
|
|||
|
|||
you could try that. it may not be the problem though. You can try a size or 2 smaller jet to see if that works. I havent rejetted mine yet, but i will when i take it back up there to ride to see if it makes a difference.
__________________
Trailmaster XRX 150 TK Variator and 1500 Spring SYC Performance Ported & Polished & Shaved 2 Valve Head, A-10 Camshaft, R2C Filter, and Hammerhead Exhaust Hammerhead 250GTS White Torque and Clutch Springs, 18g Rollers, R2C Filter, Ported Polished and Shaved Head, Hammerhead Exhaust |
#6
|
||||
|
||||
I'm having the same problem right now with my Carbide 150. I can tell you with mine, it's not a jetting issue as we've tried over 30 combinations. Waiting on a new CDI and regulator to see if it'll remedy the problem.
|
#7
|
||||
|
||||
The main jet only affects the acceleration at wide open throttle. If you are experiencing this problem at takeoff it is NOT the main jet. Either there is a slight air leak somewhere, a bit of trash in the carb somewhere, the pilot needs adjusted, or the needle and jet in the second stage needs adjusted. Even improper float level can affect the carb working right. One hard jolt such as landing from a jump or something similar can get the float valve out of adjustment and even a 1-2mm difference in this setting can have an adverse affect on the carb. try removing and cleaning the carb. remove the pilot screw ( noting first how many turns out from completely seated it is ) and blow out inside of there. Here is a link to a good description of tuning these carbs.
http://www.factorypro.com/tech/tech_...m_engines.html http://www.google.com/url?sa=t&rct=j...,d.dmg&cad=rja
__________________
MXR TrailBender 160R SYC Perf head P&P,Matched intake and exhaust, A12 cam, Orange CDI & coil, Motorio pulley, 115mm Variator and lightweight drive face,11gm Sliders, UNI, modded muffler + 200 horsepower http://www.youtube.com/watch?v=3hx-hEWl10c I'll take your insults as compliments and blame it on your lack of intelligence. |
#8
|
||||
|
||||
If it was running fine before and its not now. clean ur filter and check for air leaks first. if nothing than clean ur carb. before changing or adjusting anything. just a thought.
__________________
2. 150cc carters. 1. Baja reaction 150cc dr2 variators Jerseydevil hp. Pipes unifilters gates belts. Yellow main springs hd. Orange coils. |
#9
|
|||
|
|||
As miamieddie suggested, I started with the simple things. I just checked the spark plug and when removing the wire, the whole "head" of the plug came off leaving a screw exposed on the the plug. Is this normal?
|
#10
|
||||
|
||||
just screw the tip back on. They do screw on.
__________________
MXR TrailBender 160R SYC Perf head P&P,Matched intake and exhaust, A12 cam, Orange CDI & coil, Motorio pulley, 115mm Variator and lightweight drive face,11gm Sliders, UNI, modded muffler + 200 horsepower http://www.youtube.com/watch?v=3hx-hEWl10c I'll take your insults as compliments and blame it on your lack of intelligence. |
#11
|
||||
|
||||
Yup just screw it on and lets rock!!!!!
__________________
2. 150cc carters. 1. Baja reaction 150cc dr2 variators Jerseydevil hp. Pipes unifilters gates belts. Yellow main springs hd. Orange coils. |
#12
|
||||
|
||||
Take a close look at your connector. Some will clamp on the round tip of the plug, as traditionally in a car. Others require that plug tip to be removed and clamp the threaded stud. These grip the threads for more holding power in a high vibration circumstance. IE, mowers, industrial equipment, more preferable and secure connection.
|
#13
|
|||
|
|||
Well, I think I found the problem. One of my clamps on the fuel petcock was off so maybe it was causing a vacuum leak. Seems to be running better but time will tell. I hope it's nothing that involves taking apart the carb. Not looking forward to that.
|
#14
|
||||
|
||||
Just replaced my CDI and Regulator and it's back to running great! No more hesitation or popping on acceleration.
|
#15
|
|||
|
|||
popping
Quote:
Carb intake air box stator 8 pole fly wheel rectifer coil plug fuel pump adjusted valves and it still pops when you floor it. If you drive it a half throttle it runs good and smooth, if you mash the pedel to the floor it starts breaking up and will not accellerate. You have to back off to part throttle. I ordered a CDI but I had to order a waring harness adapter and I am waiting on it to come in so I can use the new CDI. It has oval plugs where my factory wire has sqare plugs. Both are AC cdi's. Any ideas if I am chasing the correct thing? Hope to find out what is causing this soon. Buggy cranks right up and idles great. Will run great until you go pass half throttle....I even pulled the new carb off and checked the jets to make sure they are not plugged....It is not the carb....where to look now? Or am Im on the right track? Here is a picture of the cdi I have. The orange one is the new one and the black one is the factory one. And the wiring harness is what I had to get to make it a plug and play installation. |
#16
|
||||
|
||||
Quote:
__________________
ASE Master and Toyota Master Diagnostic Certified Buggy Building Trainee '04 Dazon Raider 150 'modded' |
|
|