|
|
|
|||||||
| Mini Buggy General Discussion General Discussion forum for Mini Buggies. (American Sportworks, HammerHead, Carter, etc) |
|
|
Thread Tools |
|
#1
01-08-2014, 04:53 PM
|
|||
|
|||
show me your homemade windshields and how you attached them.
I am going to be installing a plexi-glas windshield on my yerf dog. I am pretty sure I know how I'm going to do it, but I just thought I'd see what others have done.
|
|
#2
01-08-2014, 04:59 PM
|
||||
|
||||
|
Thats one thing I don't see many people doing. Would like to see some installs myself.
|
|
#3
01-08-2014, 05:21 PM
|
||||
|
||||
|
I'd get too much mud on it to see thru while racing; i run window netting across the whole front hoop opening. After the race in the pic, I added thin acrylic to 6" up top and about 2' of the bottom of the opening to keep the worst of it off me. Still leaves an 18" or so gap with no windshield at eye level. Hole punched and ziptied to the hoop. anything strong enough to break through it (it can withstand a golf ball hit from 175 yards away-- I know that for a fact) will get caught by the netting.
word of warning re. plexi. it discolors (yellows/browns out) in UV rays and gets brittle. It also cracks real easy at edges and when cutting/drilling. You're better off with lexan. For either, I'd weld some flat tabs inside the hoop and added a rubber spacer sheet between the windshield and tab. Oversize hole for the bolt, with a nylon spacer as thick as the windshield and a nylon or rubber washer under the bolt head. Last edited by x-bird; 01-08-2014 at 05:25 PM. |
|
#4
01-08-2014, 07:33 PM
|
|||
|
|||
|
I want it for the winter riding, to block some wind.
|
|
#5
01-08-2014, 07:58 PM
|
|||
|
|||
|
Here are a couple I found online:
  
|
|
#6
01-08-2014, 08:58 PM
|
||||
|
||||
|
Looks like some are using zipties, but I guess we've got some split locking collars too! I think if I do a little wind shield I'll just go the route and get some solid, metal fasteners to do it. Oh wait, I wasn't the one considering the windshield. OR WAS I?!?!
__________________
Yerf-Dog Spiderbox  Reverse Gearbox Heavy Duty Ball Joints Heavy Duty Chain Tensioner Canvas Roof/Netting Key Start LED Brake Lights Headlights SOLD! |
|
#7
01-08-2014, 09:06 PM
|
||||
|
||||
|
Yep. Acrylic would be a better option. Not quite as impact resistant, but half the cost.
__________________
ASE Master and Toyota Master Diagnostic Certified Buggy Building Trainee '04 Dazon Raider 150 'modded' |
|
#8
01-08-2014, 09:10 PM
|
|||
|
|||
|
I'm planning on using plexiglas (acrylic) and attaching it with these:
|
|
#9
01-08-2014, 09:25 PM
|
||||
|
||||
|
I've been contemplating on a windshield. Putting weather strips on the rollbar and laying the plexi on it as cushion and drilling holes into the plexi and tie wrapping it. When drilling holes in plexi don't drill to close to the edge or it will crack. You also must drill slowly or it will also crack. Just my thought. And one more thing lots of people use lexan as bird mentioned. Its safer in case your buggy rolls it don't cut your head off.
__________________
2. 150cc carters. 1. Baja reaction 150cc dr2 variators Jerseydevil hp. Pipes unifilters gates belts. Yellow main springs hd. Orange coils. |
|
|
