BuggyMasters.Com - An On Line Mini Buggy Forum and Go Kart Forum

Go Back   BuggyMasters.Com - An On Line Mini Buggy Forum and Go Kart Forum > Technical Discussions > 150cc GY6 and Under Engine Tech

150cc GY6 and Under Engine Tech GY6 and Smaller Technical Discussion Forum

 
 
Thread Tools
  #1  
Old 06-25-2018, 07:54 AM
turbo84gn turbo84gn is offline
Lurker
 

Join Date: Jun 2018
Posts: 5
Default DIY air filter

I have seen a lot references to making your own air filter assembly, but haven’t found any good threads with useful details. They don’t make a replacement element that fits my air box so need to do it. Can I get some good examples, and if useful make it a sticky?
  #2  
Old 06-25-2018, 04:50 PM
neo71665 neo71665 is offline
Contributor
 

Join Date: Jun 2017
Posts: 284
Default

Really aint much to it.

You remove the old stuff.

Put a rubber coupler on the carb neck. I've seen some guys buy one at the hardware store and some use a piece of radiator hose. (I started off with rad hose but once I knew what I wanted ordered a silicone piece)

6 inch section of 1 1/2 inch pipe, can be as simple as PVC or you can go all out and get stainless. That slips in the rubber connector. (got SS on mine because I happened to have a piece laying around)

Put your filter on the end. (I'm running a unifilter, you need one that will fit the pipe diameter you have)

The old vacuum line that ran to the air box I see most guys just run a longer hose and shove it between the outer and inner foam on the filter. (I threaded a nipple in the pipe on mine and have an oil catch can)

Tune and rejet the carb. Suggest just paying the $6 or so on ebay for the 10 piece jet kit. Once you get it dialed in as long as you don't change elevations all the time it's set but nice to have them all for tuning vs ordering one at a time and waiting.

Last edited by neo71665; 06-25-2018 at 04:55 PM.
  #3  
Old 06-26-2018, 01:39 AM
plee911's Avatar
plee911 plee911 is offline
Contributor
 

Join Date: Feb 2018
Location: Arizona
Posts: 173
Default

If you want stainless a good option is a standard sink down spout you can get it at any hardware store and they come in different lengths.

Just got all the stuff for mine at my local hardware store
1 1/2 inch sink drain pipe 8 inch stainless $10 (you will have to cut it to get rid of the lip on the pipe but it can be done with a hack saw easy)
1 1/4 to 1 1/2 rubber coupler with hose clamps $5
Uni Filter with 1 1/2 opening ran me $20

Will eventually switch to a silicone coupler as NEO mentioned (Better quality)

Neo
Where did you find a 10 piece jet kit for that price best I could find was a 5 piece set from china.

It was $6 but only came with 5 jets and a 30 day wait
__________________
Where there is a red neck there is a way.
  #4  
Old 06-26-2018, 03:34 AM
neo71665 neo71665 is offline
Contributor
 

Join Date: Jun 2017
Posts: 284
Default

They guy I got mine from jacked the price up.

here is one for $8.75
https://www.ebay.com/itm/10Pcs-Carbu...item2aa94112c1

As for the shipping wait, you can have any 2: fast, cheap, or good
  #5  
Old 06-27-2018, 05:23 AM
plee911's Avatar
plee911 plee911 is offline
Contributor
 

Join Date: Feb 2018
Location: Arizona
Posts: 173
Default

Turbo

I haven't assembled mine yet so i will get some pics of the items and the assembly of them and post them here to help people out.


NEO
yea those are now in my watch list.
will get a set ordered.


got the 115 through 135 main jet only kit.
Would be nice to have spares and a few sizes I don't have.
plus all the pilot jets of which I have none but the ones in my carbs.
__________________
Where there is a red neck there is a way.

Last edited by plee911; 06-27-2018 at 05:25 AM.
  #6  
Old 06-27-2018, 07:09 AM
neo71665 neo71665 is offline
Contributor
 

Join Date: Jun 2017
Posts: 284
Default

I'm a carb nut from back in my drag racing days and truthfully even playing with the pilot jets a few up and down didn't see any gain or diminish in performance. I'm sure if I had Travis's gy6 dyno and time to fine tune their might be something but with just the butt dyno nothing I can see. I just like the idea of having it if I need it.

The mains I do check my tune often and have had to change as it warms and cools (buggy gets hard to start is a good key). I also knew I was gonna pretty crazy with the mods on a 150 to a blueprinted 180 so I got the whole kit. Nothing else I think everybody needs at least 2 over and 2 under of the jet size they use most often. Of course that means you need to know what size you need to start with.

If nothing else get a good set of the main jets.
  #7  
Old 07-15-2018, 11:55 PM
plee911's Avatar
plee911 plee911 is offline
Contributor
 

Join Date: Feb 2018
Location: Arizona
Posts: 173
Default here are the pics of the set up for the home made intake

here are the pics

I had the option of an 8 inch or 12 inch drain pipe in 1 1/2 inch Inside diameter I chose the 12 inch cause if I want it shorter I can cut it. ( From what I have seen at least 8 inches is what is recommended) I went stainless because I think it looks cooler and no rust to worry about.
I ended up going with a 1 1/4 inch rubber coupler same size on both sides because the sink drain wall thickness is thinner and wouldn't fit a 1 1/2 coupler snuggly.
The Uni filter fit right to it and both clamp down nice and tight.

Then it is just attached to the carb.

It will have to be supported but every kart is different so that will have to be a decision made by the kart owner for what works best for them.
Attached Images
File Type: jpg 12 inch sink drain.jpg (86.6 KB, 24 views)
File Type: jpg rubber coupler.jpg (88.4 KB, 18 views)
File Type: jpg Rubber coupler 2.jpg (85.7 KB, 18 views)
File Type: jpg sink drain and coupler.jpg (88.5 KB, 21 views)
File Type: jpg sink drain with coupler attached.jpg (88.8 KB, 16 views)
File Type: jpg IMG_20180707_060232514.jpg (94.5 KB, 20 views)
File Type: jpg assembled unit.jpg (85.1 KB, 25 views)
__________________
Where there is a red neck there is a way.

Last edited by plee911; 07-16-2018 at 12:07 AM.
 


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:22 PM.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.