|
|
|
|||||||
| 150cc GY6 and Under Engine Tech GY6 and Smaller Technical Discussion Forum |
|
|
Thread Tools |
|
#1
02-04-2010, 02:53 PM
|
||||
|
||||
Ohhhhhhh Nooooooo...... This is really bad
Ugh... So, we finally got snow in Clarksville TN last Saturday! We got about 5 inches! Of corse I had to pull the buggy out and drive it around. Driving it was a blast! Until, I was driving down a one mile stretch of road that had some slush on it and I started hearing sounds, bad sounds. At first, I just ignored it, but as I kept going, they got worse and worse. It got to the point to where home was in sight! but my engine was making extremely weird sounds, so I stopped and smoke was coming out of the CVT area. My granddad came out and towed me home. Just yesterday I took the tranny apart and what I was is in the attached pics. What you might not be able to tell is that the threads that hold the fan plate on are gone. I'm hoping and praying that ASW's warranty will cover the damages. I think they will because I haven't done any major modifications to the engine, like a big bore kit. My granddad doesn't think they will. My question here is actually two questions. #1. What on earth caused this? #2. Do you think ASW will cover the damages?
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE! |
|
#2
02-04-2010, 02:55 PM
|
||||
|
||||
|
Sorry. Here are the pics
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE! |
|
#3
02-04-2010, 03:05 PM
|
||||
|
||||
|
If I were you I would put it back to stock.I would not take out the main spring they will be to lazy to look for that.The uni,sparky and the rollers i would put back to stock then take it in and play dumb,like "i dont no" "really" "thats crazy could i have been
hurt" "should i be concerned" thing like that.That's a big reason why i did not buy a new asw because my plans were to mod it and they seemed pretty strick on there policies.Gook luck,hope thing work out for you.
__________________
 04 yerf 3206rag top  uni filter redneck intake 125 jet 16.5x6.5x8 fronts 21x11x10 holeshots on itp's coming soon 10g roller 1500rpm spring |
|
#4
02-04-2010, 03:08 PM
|
||||
|
||||
|
Thanks, I'll take the variator off and such, but do they really care about the uni?
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE! |
|
#5
02-04-2010, 03:08 PM
|
||||
|
||||
|
and i planned on playing dumb!
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE! |
|
#6
02-04-2010, 03:19 PM
|
||||
|
||||
|
Yeah I would
__________________
04 yerf 3206rag top uni filter redneck intake 125 jet 16.5x6.5x8 fronts 21x11x10 holeshots on itp's coming soon 10g roller 1500rpm spring |
|
#7
02-04-2010, 03:21 PM
|
||||
|
||||
|
If you dont they will give you some line how the uni caused the damage.Its a pain,but it will save you a ton of cash.I think if those threads are bad they have to replace the crank.If i,m right you might what to pull the spring because they may just replace the motor.
__________________
04 yerf 3206rag top uni filter redneck intake 125 jet 16.5x6.5x8 fronts 21x11x10 holeshots on itp's coming soon 10g roller 1500rpm spring |
|
#8
02-04-2010, 04:09 PM
|
||||
|
||||
|
Hahaha, that's very true about how they'll come up with some way to blame the uni, but thanks for the advice.
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE! |
|
#9
02-04-2010, 07:57 PM
|
||||
|
||||
|
That is probably a product of the 10g sliders. It looks to me like it just ate your belt up. The belt is made to withstand the stress of the stock engagement points. When you put the lighter sliders in, it allows more RPM which in turn applies more stress on the belt.
Not likely going to cover that. Still sucks it happened on a fun day. |
|
#10
02-04-2010, 08:41 PM
|
||||
|
||||
|
Which is why I'll but the stock variator back on and play dumb when they come over
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE! |
|
#11
02-04-2010, 10:51 PM
|
||||
|
||||
|
good luck on your repairs
i have always wanted to ask you how do you manage to run 55w lights olderthan
__________________
olderthan 2008 tomberline punisher 1500 spring 12g sliders 30mm cv pumper carb uni filter no rev cdi polaris xlt snowmobile shocks for front w/550 magnum springs & blaster fronts on rear and another buggy built working on mods gk-13 white spring 17 gram sliders so far |
|
#12
02-04-2010, 10:54 PM
|
||||
|
||||
|
I don't run them very often and I only replaced the ones that came with it, I didn't add two more. And thanks. I think I'm going to need it.
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE! |
|
#13
02-05-2010, 09:35 AM
|
||||
|
||||
|
ive been watching craigslist and there is a lot of cheep bikes and quads you can get for around $500 that run good.keep in mind if the one you get has good parts you can sale the parts and have a free motor.
good luck
__________________
http://www.youtube.com/watch?v=IUgir...ature=g-t=2668 FABRICATION ITS HARDER THAN YOU THINK |
|
#14
02-05-2010, 09:49 AM
|
||||
|
||||
|
Thanks
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE! |
|
#16
02-11-2010, 02:47 PM
|
||||
|
||||
|
josh
what have you heard on your buggy olderthan
__________________
olderthan 2008 tomberline punisher 1500 spring 12g sliders 30mm cv pumper carb uni filter no rev cdi polaris xlt snowmobile shocks for front w/550 magnum springs & blaster fronts on rear and another buggy built working on mods gk-13 white spring 17 gram sliders so far |
|
#17
02-11-2010, 03:53 PM
|
||||
|
||||
|
I haven't called them yet because I haven't put the stock parts back on it, but I will keep y'all posted.
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE! |
|
#18
02-11-2010, 04:03 PM
|
||||
|
||||
|
lol this is great
__________________
MY HELIX -20' maxxis tires -1 1/2in.UNI air filter -gutted exaust -extended lugs -headlights -reflectors -my stickers -adjusted suspension -ground out hubs (to fit on the tires) helix 150 |
|
#19
02-11-2010, 04:04 PM
|
||||
|
||||
|
What is?
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE! |
|
#20
02-11-2010, 05:16 PM
|
||||
|
||||
|
i would not have been able to wait
i usualy lose on a repair if i did not do it myself but i hate waiting olderthan
__________________
olderthan 2008 tomberline punisher 1500 spring 12g sliders 30mm cv pumper carb uni filter no rev cdi polaris xlt snowmobile shocks for front w/550 magnum springs & blaster fronts on rear and another buggy built working on mods gk-13 white spring 17 gram sliders so far |
|
|
