BuggyMasters.Com - An On Line Mini Buggy Forum and Go Kart Forum

Go Back   BuggyMasters.Com - An On Line Mini Buggy Forum and Go Kart Forum > General Mini Buggy and Go Kart Forums > Go Kart General Discussion

Go Kart General Discussion Forum for general go kart discussion.

 
 
Thread Tools
  #1  
Old 04-19-2021, 10:18 PM
Mayito88's Avatar
Mayito88 Mayito88 is offline
Lurker
 

Join Date: Mar 2021
Location: Houston
Posts: 11
Default Oil smells like gas!!!

Hi everyone... I just bought this buggy for my kids and before anything I changed the engine oil and I noticed the oil smells weird 😳.... So after changing the oil I let my kids turn it on. White smoke was coming out the exhaust and we decided to park it. I let it set all night and this morning I decided to check the oil level again.... And I noticed the oil smells like gas again and it was very thin.. I used 10w-40... But it now looks like dirty water.... What could be the problem??? Any help or advice will be very appreciated. Thanks!
Attached Images
File Type: jpg IMG_20210418_170452277.jpg (96.3 KB, 2 views)
File Type: jpg IMG_20210419_191659219.jpg (95.7 KB, 2 views)
  #2  
Old 04-20-2021, 12:02 PM
liduno liduno is offline
Heavy Contributor
 

Join Date: Aug 2014
Posts: 702
Default

Sounds like you may have a float valve with some crud in it, not allowing it to close. I would also check the petcock on the tank. If it's vacuum operated it shouldn't flow any gas unless the engine is running.
  #3  
Old 04-24-2021, 03:33 PM
Mayito88's Avatar
Mayito88 Mayito88 is offline
Lurker
 

Join Date: Mar 2021
Location: Houston
Posts: 11
Default

I just replace the carburator... And change the oil 2 times already... But now the smoke smells like oil... Should I replace the head cylinder?
Attached Images
File Type: jpg IMG_20210424_100031847.jpg (93.7 KB, 0 views)

Last edited by Mayito88; 04-26-2021 at 02:24 PM.
  #4  
Old 04-24-2021, 10:27 PM
liduno liduno is offline
Heavy Contributor
 

Join Date: Aug 2014
Posts: 702
Default

I think I would do a compression test before I decided to replace any major engine components.
  #5  
Old 04-25-2021, 11:48 PM
Mayito88's Avatar
Mayito88 Mayito88 is offline
Lurker
 

Join Date: Mar 2021
Location: Houston
Posts: 11
Default

What should be the reading? For the test?
Attached Images
File Type: jpg IMG_20210427_174337363.jpg (98.2 KB, 2 views)

Last edited by Mayito88; 04-27-2021 at 05:52 PM.
  #6  
Old 05-01-2021, 03:56 PM
Mayito88's Avatar
Mayito88 Mayito88 is offline
Lurker
 

Join Date: Mar 2021
Location: Houston
Posts: 11
Default

My oil doesn't smells like gas anymore... But I still have a lot of smoke coming out.... So I decided to remove the head of the engine and fund this "crispy" black layer on top of the Piston... Should a replace the head piston assembly? I don't see any scratches on the cylinder wall... Help me please.
Attached Images
File Type: jpg IMG_20210501_154308808.jpg (93.9 KB, 2 views)
File Type: jpg IMG_20210501_154630195.jpg (93.4 KB, 2 views)
File Type: jpg IMG_20210501_154507300.jpg (91.6 KB, 2 views)
  #7  
Old 05-03-2021, 01:35 PM
liduno liduno is offline
Heavy Contributor
 

Join Date: Aug 2014
Posts: 702
Default

I can't remember exactly what the compression should be, maybe like 120 130? The piston and cylinder don't look bad at all to me though. There's a little more carbon on the valve than usual, but I don't think that's really an issue.

I used to pour a little water into the carb of a revving engine to clean up carbon. I would use a dixie cup and slowly pour it in while revving the engine. It causes the carbon to crystalize and shoots it out the exhaust.

Are you sure the exhaust doesn't have oil in it? How does the buggy run despite the smoke?
  #8  
Old 05-05-2021, 07:59 AM
Mayito88's Avatar
Mayito88 Mayito88 is offline
Lurker
 

Join Date: Mar 2021
Location: Houston
Posts: 11
Default

The buggy is running good.... I clean the piston and the valves looking like new... Assemble the engine back. And the smoke still coming out.. maybe a little bit more 🙄... Even after letting the engine run for about an hour... And adding some piston rig sealer"Rislone ring sealer" what can I do now?
  #9  
Old 05-06-2021, 12:26 AM
metalstudman1's Avatar
metalstudman1 metalstudman1 is offline
Super Moderator
 

Join Date: Aug 2009
Location: Belmont,NC (elevation 534')
Posts: 2,668
Default

The smoking should go away after a few hard hours of driving. I use a lot of used mufflers off various scraped bikes, oil burning motors and it does take a minute to burn off! If the smoke is blue then it's your motor needing rings, if the smoke is more white/black then it's left over oil & gas in the muffler.I didn't think your engine looked that bad-if you don't run the motor WOT a lot then it gets that type of carbon build up.
  #10  
Old 05-07-2021, 09:49 PM
Mayito88's Avatar
Mayito88 Mayito88 is offline
Lurker
 

Join Date: Mar 2021
Location: Houston
Posts: 11
Default Found the problem!!!!

🤔After installing a new piston. I still noticing same problem to much smoke and oil getting lower on the engine...I Decide to inspect the Valves seals.👀.. .... And that was the problem!😑 they were leaking oil... I changed both of the seals and no more smoke or oil getting low.... Thanks everyone for your help... And I hope someone having the same issue find this post helpful... Thanks again everyone!!!! 😁😁😁😁
Attached Images
File Type: jpg IMG_20210507_190548460.jpg (93.0 KB, 0 views)
File Type: jpg IMG_20210507_203539707.jpg (92.8 KB, 0 views)
 


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:28 AM.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.