BuggyMasters.Com - An On Line Mini Buggy Forum and Go Kart Forum

Go Back   BuggyMasters.Com - An On Line Mini Buggy Forum and Go Kart Forum > Technical Discussions > 150cc GY6 and Under Engine Tech

150cc GY6 and Under Engine Tech GY6 and Smaller Technical Discussion Forum

 
 
Thread Tools
  #1  
Old 09-09-2009, 08:00 PM
BuggyMaster's Avatar
BuggyMaster BuggyMaster is offline
Administrator
 

Join Date: Jul 2009
Posts: 2,312
Default How do you add a UNI filter to a GY6 helix or carbide?

This has been asked a few times so I thought I would start a quickie thread on it.

Look at the pic below. That is a complete setup for a helix or a carbide. It would likely work on any GY6 but the variable comes in when deciding how to connect the carb to the UNI. You can't connect it directly because the frame bar would interfere.

What you do is go to lowes or home depot and get a piece of drain. This same kind of drain used for your kitchen sink so find the plumbing section.

You need the drain pipe, a rubber coupler, and a hose clamp. Take the UNI with you so you can get the correct size pipe (I think it is 1.5 inches). Once you have the right size pipe, get a rubber coupler (that's the grey piece on the right side of the drain pipe in the pic). It connects from the pipe to your carb. It will be found in the same section as the drain pipe. Then get one hose clamp. It connects the rubber coupler to the pipe and you use your stock hose clamp to connect to the carb.

The only thing you have to do otherwise is measure how far out you need the UNI to come out to clear the frame and you cut the drain pipe to that length and bolt it all together.



See this thread for how to rejet your carb:

http://www.buggymasters.com/forum/showthread.php?t=168
  #2  
Old 09-09-2009, 09:25 PM
Xrims's Avatar
Xrims Xrims is offline
Lite Contributor
 

Join Date: Sep 2009
Location: East Peoria,IL
Posts: 94
Default

I dont no about the Helix but on the Carbide I was able to disconnect the stock air tube from the air box and put a Uni filter on the end of the tube.Made a huge difference,put in a 136 main jet to.Total for upgrade 20.00.
  #3  
Old 09-10-2009, 02:13 PM
foxracer45's Avatar
foxracer45 foxracer45 is offline
Contributor
 

Join Date: Aug 2009
Location: new york
Posts: 222
Default

does the 136 work like you never changed it or does it stall and stuff..?
__________________
heliX 150cc
-uni filter
-rotated tires
-stereo
-adjusted suspension
-lights
-soon hammerhead performance exhaust
HELIX
  #4  
Old 09-10-2009, 04:19 PM
Xrims's Avatar
Xrims Xrims is offline
Lite Contributor
 

Join Date: Sep 2009
Location: East Peoria,IL
Posts: 94
Default

The 136 works great good plug burn.Does seem not as spunky from a dead stop take off,but gained 4 mph on over all speed.Ordered a iratium plug hopeing to bring the low end spunk back.Over all am very pleased with the 136 main jet.Tried a 132.5 and keep the quick take offs but the plug color looked alittle hot.
  #5  
Old 09-26-2009, 07:37 PM
24evanwilson's Avatar
24evanwilson 24evanwilson is offline
Senior Member
 

Join Date: Jul 2009
Location: Indiana Mostimes, NC sometimes
Posts: 1,253
Default

got mine done
__________________
MY HELIX
-20' maxxis tires
-1 1/2in.UNI air filter
-gutted exaust
-extended lugs
-headlights
-reflectors
-my stickers
-adjusted suspension
-ground out hubs
(to fit on the tires)



helix 150
  #6  
Old 08-22-2018, 12:25 AM
BuggyMaster's Avatar
BuggyMaster BuggyMaster is offline
Administrator
 

Join Date: Jul 2009
Posts: 2,312
Default

Another old post but useful! Bump!
  #7  
Old 08-22-2018, 01:13 AM
plee911's Avatar
plee911 plee911 is offline
Contributor
 

Join Date: Feb 2018
Location: Arizona
Posts: 173
Default

This thread shows what I did for mine with the specific parts I got.

http://buggymasters.com/forum/showthread.php?t=6404

Currently im running the full 12 inch drain pipe because it puts the uni filter out to where it rests on the back crossbar for support. Planning to shorten it to 7 or 8 inches once I get a support bracket for the drain pipe figured out.
__________________
Where there is a red neck there is a way.
 


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:27 PM.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.