|
|
|
|||||||
| 150cc GY6 and Under Engine Tech GY6 and Smaller Technical Discussion Forum |
|
|
Thread Tools |
|
#1
03-22-2010, 01:55 PM
|
||||
|
||||
Will this fit?
I found a HH exhaust and I was wondering if it will fit. It says it's for the HH 150, but since they both run the same engine, I thought it'll fit. Here it is. http://www.*************************...%20Exhaust.jpg http://www.*************************...ANCE%20EXHAUST
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE! |
|
#2
03-22-2010, 01:55 PM
|
||||
|
||||
|
Oooook then. Nevermind then
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE! |
|
#3
03-22-2010, 02:28 PM
|
||||
|
||||
|
You will need to find out for sure from the seller, if I remember correctly the header pipe on those are routed to the passenger side. I could be wrong. They are a good performance exhaust.
__________________
09 Joyner Sand Viper 250 08 Joyner Sand Viper 250 2009 Joylaris 400 Screamer http://www.youtube.com/watch?v=eeulR4W1_PU |
|
#4
03-22-2010, 11:53 PM
|
||||
|
||||
|
the carbide and helix use the same engine as the hh twister 200 i'm not sure if the hh 150's are the same.They did not produce the 200's for very long.
__________________
asw carbide 1500 main and clutch springs HP clutch and bell koso variator performance cdi uni redneck intake fmf exaust 9gram rollers 39 tooth sprocket 140main and 40 pilot jet |
|
#5
03-23-2010, 12:38 AM
|
||||
|
||||
|
Yeah the 200 was essentially a 150 branded as a 200 but they could not get the 200cc lined out, that is what I recall from a discussion about them with Bige.
__________________
09 Joyner Sand Viper 250 08 Joyner Sand Viper 250 2009 Joylaris 400 Screamer http://www.youtube.com/watch?v=eeulR4W1_PU |
|
#6
03-23-2010, 04:18 AM
|
||||
|
||||
|
Should fit fine.
|
|
#7
03-23-2010, 12:08 PM
|
||||
|
||||
|
seriously,what buggymaster said
__________________
MY HELIX -20' maxxis tires -1 1/2in.UNI air filter -gutted exaust -extended lugs -headlights -reflectors -my stickers -adjusted suspension -ground out hubs (to fit on the tires) helix 150 |
|
#8
03-23-2010, 12:34 PM
|
||||
|
||||
|
Alrighty then.
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE! |
|
|
