|
|
|
|||||||
| 150cc GY6 and Under Engine Tech GY6 and Smaller Technical Discussion Forum |
|
|
Thread Tools |
|
#1
01-24-2014, 10:30 AM
|
|||
|
|||
variator removal
I've pulled apart my motor to do some upgrades, but I'm having trouble removing the last bit of the variator so I can pull my crank out. Any tips?
__________________
2013 Trailmaster XRX 150 Type 86 stroker Taida 4V head with 23/22mm valves, forged 4V piston,Taida 62mm jug,forged Taida 8200 KDU stroker crank, Koso high-flow oil pump, Taida case half w/ oil cooler ports, Setrab oil cooler,TrailTec Vapor, Mikuni VM26-606, aluminum 30mm intake, Uni filter, aluminum stack, Hammerhead racing exhaust, MotoRio adjustable CDI/HO Coil, Iridium plug, Full Dr Pulley CVT kit w/ 16g sliders, JD's Mikuni slide kit 2014 Kandi 90B |
|
#2
01-24-2014, 12:07 PM
|
|||
|
|||
What bit?
__________________
2009 ASW Carbide Uni filter, outerwears, redneck intake, 130 main jet, 38 pilot jet, drilled exhaust, DR Pulley 9g sliders, 2000rpm clutch spring, adjustable CDI and 39T sprocket 2009 ASW Carbide 39T sprocket, DR Pulley 10g sliders, drilled exhaust 2010 ASW Vector bone stock |
|
#3
01-24-2014, 12:21 PM
|
|||
|
|||
|
Not the piece with the rollers. The other one with the plastic guides in the middle of each section.
__________________
2013 Trailmaster XRX 150 Type 86 stroker Taida 4V head with 23/22mm valves, forged 4V piston,Taida 62mm jug,forged Taida 8200 KDU stroker crank, Koso high-flow oil pump, Taida case half w/ oil cooler ports, Setrab oil cooler,TrailTec Vapor, Mikuni VM26-606, aluminum 30mm intake, Uni filter, aluminum stack, Hammerhead racing exhaust, MotoRio adjustable CDI/HO Coil, Iridium plug, Full Dr Pulley CVT kit w/ 16g sliders, JD's Mikuni slide kit 2014 Kandi 90B |
|
#4
01-24-2014, 12:25 PM
|
|||
|
|||
|
Ya the backing plate, the roller gets stuck pretty good sometimes preventing you from removing the backing plate.
I use a 3 jaw puller from harber freight. I have a pic in one of my threads, i will find it and post it.
__________________
2009 ASW Carbide Uni filter, outerwears, redneck intake, 130 main jet, 38 pilot jet, drilled exhaust, DR Pulley 9g sliders, 2000rpm clutch spring, adjustable CDI and 39T sprocket 2009 ASW Carbide 39T sprocket, DR Pulley 10g sliders, drilled exhaust 2010 ASW Vector bone stock |
|
#5
01-24-2014, 12:28 PM
|
|||
|
|||
|
__________________
2009 ASW Carbide Uni filter, outerwears, redneck intake, 130 main jet, 38 pilot jet, drilled exhaust, DR Pulley 9g sliders, 2000rpm clutch spring, adjustable CDI and 39T sprocket 2009 ASW Carbide 39T sprocket, DR Pulley 10g sliders, drilled exhaust 2010 ASW Vector bone stock |
|
#6
01-24-2014, 01:12 PM
|
|||
|
|||
|
Oh cool, Thx!
__________________
2013 Trailmaster XRX 150 Type 86 stroker Taida 4V head with 23/22mm valves, forged 4V piston,Taida 62mm jug,forged Taida 8200 KDU stroker crank, Koso high-flow oil pump, Taida case half w/ oil cooler ports, Setrab oil cooler,TrailTec Vapor, Mikuni VM26-606, aluminum 30mm intake, Uni filter, aluminum stack, Hammerhead racing exhaust, MotoRio adjustable CDI/HO Coil, Iridium plug, Full Dr Pulley CVT kit w/ 16g sliders, JD's Mikuni slide kit 2014 Kandi 90B |
|
#7
01-24-2014, 05:09 PM
|
||||
|
||||
|
how ive always managed is installing the nut back on and giving it a good gentle whack with a brass hammer.has worked everytime for me
__________________
MASTERBATES TM 150 XRX-P&P head,A13cam,opened exhaust,140 main,38 pilot,adj cdi, perf coil,115mm variaitor,12 gm rollers,NCYpulley,2000 rpm springs,racing clutch,taller rear tires,and etc. 
|
|
|
