|
|
|
|||||||
| 150cc GY6 and Under Engine Tech GY6 and Smaller Technical Discussion Forum |
|
|
Thread Tools |
|
#1
06-17-2016, 03:06 PM
|
||||
|
||||
Trouble with gy6 150 getting cranked
Hey everyone, I'm working on another buggy with the gy6 150...having trouble getting it to crank, and when it finally does, can't give it any gas without dieing..got the buggy off a guy that had it sittin up for a while...so went ahead and ordered and out on
1. New 26mm carb 2. New fuel petcock 3. New fuel and vent lines 4. New manifold.. 5. New plug I have great blue spark when it turns over...anybody think it could be the valves out??? If so what do they need to be set at? Need some help bad!! |
|
#2
06-18-2016, 12:21 AM
|
||||
|
||||
|
.004 both sides
__________________
2. 150cc carters. 1. Baja reaction 150cc dr2 variators Jerseydevil hp. Pipes unifilters gates belts. Yellow main springs hd. Orange coils. |
|
#4
06-18-2016, 01:23 AM
|
||||
|
||||
|
Some are just pigheaded in the automatic choke department to where you just gotta let it sit there and idle long enough for the choke to start closing off and then you can slowly start feathering into the gas until its fully warm. Have seen this many, many times.
When valve adjustment helps the idle its because the valve seats have sunk a little which takes out any lash. You see this mostly on newer machines. Eventually the seats sink as much as they are going to go and your adjustment remains good. I do mine .003-.004 on both cause I like a quiet engine but some recommend more on the intake side. From your description I think you have a pigheaded choke situation. |
|
#5
06-20-2016, 12:10 PM
|
||||
|
||||
|
I will recheck the choke/fuel enricher..but i have tried 4 different carbs and they all do the same thing...will these buggies crank but not run good if the timming is out one tooth or so???? Also, just found a rat nest in the pick-up coil/ cooling fan area on this buggy...lmbo!!!! They might have nawed up a wire or two, i will be pulling the magnento, pick-up coil off and check it all over real good in the next couple of days..
|
|
#6
06-20-2016, 12:13 PM
|
||||
|
||||
|
Buggymaster, i let this machine run for about 6-7 mins the other day, just at idle, and i never could feather the throttle any without dying out...i hoping i have a chewed up wire from the rats that got in this buggy.. I don't know on this one
|
|
#7
06-20-2016, 03:34 PM
|
||||
|
||||
|
I had this problem for me it ended up being the fuel petcock. replaced it and it ran smooth as a new buggy not sure if it is the same for you but worth a shot. as a test you could set up a simple gravity feed fuel source.
|
|
#8
06-20-2016, 05:55 PM
|
||||
|
||||
|
What was the carb designed for ( the new one you put on)? Why not clean the existing carb which you know is jetted properly? Not likely an electrical problem. Typically an electrical problem is all or none. Not always the case but ysually. The other way to tell is give it a little shot of catb cleaner as someone else oedals the gas. If it takes...then you have fuel issue. If it kills it quicker than could have a too-much-fuel issue.
|
|
#9
06-21-2016, 08:08 AM
|
||||
|
||||
|
I tried to replace the fuel petcock and it still does the same thing...i went back with the same design as the original carb, only difference is this one is a 26 mm...still jetted the same..running a 105 main jet...had to replace because the original carb was missing in action...did not have one on it when i got the buggy...one thing i just found out!! This motor came off a helix 150, and the buggy i'm working on is a trailmaster....the original trailmaster motor, i was told, was blown up....so, the feller im working on the buggy for, replaced the motor with a helix gy6 150...i do see alot of cut wires and splices all over the place on this buggy, so that is why i was thinking i had an electrical issue too..he cut away all the plug in's and has wire nuts on the wires....so, i guess i need to find a helix 150 wiring harness??? Any ideas???
|
|
#11
06-21-2016, 10:20 AM
|
||||
|
||||
|
Well one thing that is significant is the Helix is one of the few buggies that uses a DC based CDI box. I am curious how all that is wired. Let me think on this a bit.
|
|
#12
06-21-2016, 10:23 AM
|
||||
|
||||
|
Any chance you have a timing light? Its great for knowing if you have spark or not while the machine is running. You simply point it on the floor and give it gas and if the spark dies first and then the engine you know you have an electrical issue.
|
|
#13
06-21-2016, 12:35 PM
|
||||
|
||||
|
Where did you find a 26mm carb? ive only seen one and it came off of a carter brothers mid size 150.
__________________
Buggy Dealer Crossfire 250r IRS (400cc swap in progress) Crossfire 250r (SYM 250) HH250SS..RIP (IRS donor for the crossfire) HammerHead 150 Gs Moon buggy 150 Many other random parts buggys (still never have what im needing tho :/ ) |
|
#14
06-22-2016, 08:19 AM
|
||||
|
||||
BuggyMaster, I FOUND A WIRING SCHEMATIC OF A HELIX 150 AND A TRAILMASTER 150, AND LAST NIGHT I SAT DOWN AND STARTED ALL OVER WITH THE WIRING ON THIS BUGGY...AND THE TRAILMASTER AND THE HELIX THAT I'M WORKING ON ARE BOTH DC FIRE CDI BUGGIES...IT ONLY TOOK ABOUT 1 1/2 HOURS AND I HAD IT RUNNING GOOD...THE GUY THAT I'M WORKING ON THIS CART FOR HAD IT WIRED ALL MESSED UP!!! HE DIDN'T HAVE THE TRIGGER WIRE, OFF THE STATOR, WIRED INTO ANYTHING...AND ON THIS CART THE BLACK WITH A RED STRIPE COMING OUT OF THE STATOR, DOESN'T GO TO ANYTHING...WELL, HE HAD IT AS A GROUND WIRE, AND HE TIED IT INTO 3 DIFFERENT WIRES!!!
 ALSO, HE HAD THE CHOKE/FUEL ENRICHER WIRED TO BOTH A GROUND WIRE FROM THE FRAME AND A GOUND TO THE BATTERY!!!  IT IS SUSPOSED TO WIRE UP TO THE YELLOW WIRE OUT OF THE VOLTAGE REGULATOR AND THE GREEN WIRE THAT GOES TO THE 10AMP RESISTER ON THIS BUGGY...I DON'T EVEN SEE HOW THE BUGGY WOULD START AT ALL IN THE BEGINNING....BUT, SHE RUNS LIKE A CHAMP NOW, THANKS EVERYONE FOR ALL THE HELP AND SUGGESTIONS...YALL DON'T KNOW HOW MUCH I REALLY APPRECIATE IT ALL....
|
|
#15
06-22-2016, 08:27 AM
|
||||
|
||||
|
BEEFKING69, I FOUND THE 26mm CARB ON AMAZON I BELIEVE...THEY HAD SOME THAT I LOOKED AT AND, I THINK I SEEN SOME ON EBAY TOO..I HAVE PUT THE 26mm ON THE LAST 4 BUGGIES I HAVE WORKED ON AND THEY DO REALLY GOOD.. THEY USUALLY COME WITH A 105-110 MAIL JET IN THEM...NOW ON 3 OF THE BUGGIES I HAD TO REJET THE CARB, BECAUSE THEY HAD SOME MODS DONE LIKE: HIGH FLO AIR INTAKE, HOT COIL, ADVANCED CDI, PERFORMANCE VARIATOR WITH 11 GRAIN SLIDERS, MAIN CLUTCH SPRING CHANGED OUT, DIFFERENT CLUTCHES, AND MODIFIED EXHAUST SYSTEMS..SO WITH THOSE WE WENT WITH ANYWHERE FROM A 115-125...JUST HAD TO PLAY AROUND WITH THEM AND SEE WHERE THEY RAN THE BEST AT...
|
|
#16
06-23-2016, 02:43 AM
|
||||
|
||||
|
Engine/butterfly side true 26mm ID? ive seen alot advertised as 26mm but they were really 24mm
__________________
Buggy Dealer Crossfire 250r IRS (400cc swap in progress) Crossfire 250r (SYM 250) HH250SS..RIP (IRS donor for the crossfire) HammerHead 150 Gs Moon buggy 150 Many other random parts buggys (still never have what im needing tho :/ ) Last edited by BEEFKING69; 06-23-2016 at 02:55 AM. |
|
#18
06-23-2016, 02:58 PM
|
||||
|
||||
|
How much?
__________________
Buggy Dealer Crossfire 250r IRS (400cc swap in progress) Crossfire 250r (SYM 250) HH250SS..RIP (IRS donor for the crossfire) HammerHead 150 Gs Moon buggy 150 Many other random parts buggys (still never have what im needing tho :/ ) |
|
#19
06-23-2016, 04:02 PM
|
||||
|
||||
|
Quote:
__________________
2010 Carter Interceptor GTR 300 2010 Hammerhead 250 SS 2015 Kandi 49FM5 110cc 2015 Hammerhead GTS 250-SOLD 2008 Kazuma Coyote 150-SOLD |
|
#21
02-24-2017, 07:16 AM
|
|||
|
|||
|
Quote:
|
|
|
