BuggyMasters.Com - An On Line Mini Buggy Forum and Go Kart Forum

Go Back   BuggyMasters.Com - An On Line Mini Buggy Forum and Go Kart Forum > Technical Discussions > Electrical Tech

Electrical Tech General Tech for Electrical issues not related to specific engines (Lights etc)

 
 
Thread Tools
  #1  
Old 09-29-2013, 06:40 PM
zman007007's Avatar
zman007007 zman007007 is offline
Senior Member
 

Join Date: Dec 2012
Location: Gray Court,S.C.
Posts: 1,476
Default brake light crossfire 150R

Has anyone put a brake light on a crossfire 150R? I don't see any type of electrical switch on the master cylinder. The wiring diagram I have doesn't show any brake light wire either.
  #2  
Old 09-29-2013, 06:50 PM
Masteryota's Avatar
Masteryota Masteryota is offline
Senior Member
 

Join Date: Dec 2012
Location: North Florida
Posts: 1,155
Default

I see a lot of people replacing the banjo bolt on the caliper with one of these and adding a light like this to that circuit. Seems the easiest way to add a brake light. You would need to double check the thread size, but you get the idea.
__________________
ASE Master and Toyota Master Diagnostic Certified
Buggy Building Trainee

'04 Dazon Raider 150 'modded'
  #3  
Old 09-30-2013, 06:00 PM
zman007007's Avatar
zman007007 zman007007 is offline
Senior Member
 

Join Date: Dec 2012
Location: Gray Court,S.C.
Posts: 1,476
Default

I already have the brake light. That looks like something that would work, but I hate having to wait for it to come from China. what does the other carts that have brake lights use and would one of those be available.
  #4  
Old 09-30-2013, 06:18 PM
Masteryota's Avatar
Masteryota Masteryota is offline
Senior Member
 

Join Date: Dec 2012
Location: North Florida
Posts: 1,155
Default

Quote:
Originally Posted by zman007007 View Post
I already have the brake light. That looks like something that would work, but I hate having to wait for it to come from China. what does the other carts that have brake lights use and would one of those be available.
There are more local items on there, just a bit higher in price. Different thread pitches are also available. I looked a Kinroad diagram, and it showed a switch at the master cylinder, likely similar to what I linked. You could also put the above type switch on the master as well. Just my $0.02
__________________
ASE Master and Toyota Master Diagnostic Certified
Buggy Building Trainee

'04 Dazon Raider 150 'modded'
  #5  
Old 09-30-2013, 07:26 PM
zman007007's Avatar
zman007007 zman007007 is offline
Senior Member
 

Join Date: Dec 2012
Location: Gray Court,S.C.
Posts: 1,476
Default

thanks Master, I just bought one of the spring type switches. I believe I can make it work.
  #6  
Old 09-30-2013, 07:36 PM
Tionestajeeper's Avatar
Tionestajeeper Tionestajeeper is offline
Lite Contributor
 

Join Date: Dec 2012
Posts: 39
Default

Zman does your master cylinder have a leed for the original brake lite? Mine had one and the terminal was corroded and I replaced it with a led third tail lite from a escalade I had laying around and worked fine.
__________________
Progress photos at my Facebook page.
Tionesta jeeper
http://youtu.be/_X9Ncq60LJA
  #7  
Old 09-30-2013, 07:45 PM
ckau's Avatar
ckau ckau is offline
Heavy Contributor
 

Join Date: Dec 2009
Location: central North Carolina
Posts: 915
Default

Most buggys that come factory with brake lights use a duel piston/ duel port master cylinders. Two ports off one piston are used for the front brakes only one port off the other piston is used for a rear brake. the spare port has a pressure switch for the brake light. If you have front brakes and a rear brake chances are you have an extra port on the rear brake side to install a switch. you'll have to remove the plug to confirm thread size. I'm thinking 8x1.25 but I could be wrong. Remember you'll have to bleed the brakes once that plug is removed. Any dealer can supply the switch. If you don't have a spare port on the master get one of these,http://www.ebay.com/itm/WPS-Universa...96acb3&vxp=mtr
The master cylinder switch is a ground unit. the body of the switch gets chassis ground by screwing it into the master. When pressure activated sends ground to the tail light, one wire needed for connection at tail light. The universal is just a momentary switch . It has to have ground supplied then sends ground to the taillight when the spring is pulled.(2 wires) This switch can be connected to the pedal or any part of the linkage and doesn't require a brake bleed after installed.
  #8  
Old 09-30-2013, 07:50 PM
zman007007's Avatar
zman007007 zman007007 is offline
Senior Member
 

Join Date: Dec 2012
Location: Gray Court,S.C.
Posts: 1,476
Default

I have looked twice and I dont see any extra ports on it. and none plugged either. just blank places like you could drill and tap, but I ain't going to that trouble.
  #9  
Old 09-30-2013, 07:51 PM
zman007007's Avatar
zman007007 zman007007 is offline
Senior Member
 

Join Date: Dec 2012
Location: Gray Court,S.C.
Posts: 1,476
Default

I figured the pull switch type would be the simplist
  #10  
Old 09-30-2013, 07:54 PM
zman007007's Avatar
zman007007 zman007007 is offline
Senior Member
 

Join Date: Dec 2012
Location: Gray Court,S.C.
Posts: 1,476
Default

I looked at the one you are talking about ckau but I think the spring type woud be the easiest. I am talking about the ones that have the round barrel type end on it. I can make a little bracket to mount it in .
  #11  
Old 09-30-2013, 07:57 PM
x-bird's Avatar
x-bird x-bird is offline
Power User
 

Join Date: Oct 2011
Location: Penciltucky
Posts: 2,518
Default

i'd have to take a pic, but i mounted a vending machine coin mech microswitch by the pivot bellcrank on my brake setup. had to bend the trigger wire around a bit to ge t it dialed in, but it works well enough.
  #12  
Old 09-30-2013, 08:32 PM
Masteryota's Avatar
Masteryota Masteryota is offline
Senior Member
 

Join Date: Dec 2012
Location: North Florida
Posts: 1,155
Default

Quote:
Originally Posted by x-bird View Post
i'd have to take a pic, but i mounted a vending machine coin mech microswitch by the pivot bellcrank on my brake setup. had to bend the trigger wire around a bit to ge t it dialed in, but it works well enough.
Boy, you just have access to all sorts of goodies don't you?
__________________
ASE Master and Toyota Master Diagnostic Certified
Buggy Building Trainee

'04 Dazon Raider 150 'modded'
  #13  
Old 10-01-2013, 07:31 PM
zman007007's Avatar
zman007007 zman007007 is offline
Senior Member
 

Join Date: Dec 2012
Location: Gray Court,S.C.
Posts: 1,476
Default

I bought the spring type one.
 


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:24 AM.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.