![]() |
![]() |
#1
|
||||
|
||||
![]()
DOES ANYBODY ACTUALLY RIDE ? SEEM'S LIKE LATELY IT'S ALL - TRY TO GET IT TO RUN , TRY TO MOD. IT , TRY TO BUY IT , TRY TO SELL IT . HOW ABOUT TRYING TO RIDE IT !!!!!!! -- AND POST SOME STORIES , AND SOME PIC.'S . IT'S SEVEN DEGREES HERE , AND I HAVEN'T RIDDEN IN FIVE MONTHS !!!! HELP A BROTHER OUT
![]()
__________________
2011 BMS KING COBRA 150 Sold YERF DOG SPIDERBOX's Sold YERF DOG 3203's. Sold MANCO SILVER FOX. Sold 2009 POLARIS 500 HO SPORTSMAN 4X4 2002 POLARIS 500 HO SPORTSMAN 4X4 2000 POLARIS MAGNUM 2X4 HALF A DOZEN CHEVY 4X4's NEED-MO-BUGGY ![]() |
#2
|
||||
|
||||
![]()
lol it probably will be this way for the next month or so.
|
#3
|
||||
|
||||
![]()
here in beautiful S.C. it is 46 degrees with expected high of 52 degrees and mostly sunny today with 0 chance of rain.
|
#4
|
|||
|
|||
![]()
Riding in south Florida whenever I get the urge.
![]() |
#5
|
|||
|
|||
![]()
3 feet of snow here with another foot on the way Monday. Got the motor out at the moment. Plus my buddy who had 200 acres of land that I rode on, sold it.. Gotta find a new place to ride around MA..
__________________
2013 Trailmaster XRX 150 Type 86 stroker Taida 4V head with 23/22mm valves, forged 4V piston,Taida 62mm jug,forged Taida 8200 KDU stroker crank, Koso high-flow oil pump, Taida case half w/ oil cooler ports, Setrab oil cooler,TrailTec Vapor, Mikuni VM26-606, aluminum 30mm intake, Uni filter, aluminum stack, Hammerhead racing exhaust, MotoRio adjustable CDI/HO Coil, Iridium plug, Full Dr Pulley CVT kit w/ 16g sliders, JD's Mikuni slide kit 2014 Kandi 90B |
#6
|
|||
|
|||
![]()
What part of Mass you from Bob? I grew up in Mass.
|
#7
|
||||
|
||||
![]()
Got to mod my normal ride to get it going again (stole the rear shocks and seatbelts for the latest build) and that has to wait until i finish my latest build ...otherwise, i'd be riding even with the foot of snow on the ground and sub freezing temps ...
|
#8
|
|||
|
|||
![]()
Newburyport. Right on the coast, just below New Hampshire..
__________________
2013 Trailmaster XRX 150 Type 86 stroker Taida 4V head with 23/22mm valves, forged 4V piston,Taida 62mm jug,forged Taida 8200 KDU stroker crank, Koso high-flow oil pump, Taida case half w/ oil cooler ports, Setrab oil cooler,TrailTec Vapor, Mikuni VM26-606, aluminum 30mm intake, Uni filter, aluminum stack, Hammerhead racing exhaust, MotoRio adjustable CDI/HO Coil, Iridium plug, Full Dr Pulley CVT kit w/ 16g sliders, JD's Mikuni slide kit 2014 Kandi 90B |
#9
|
|||
|
|||
![]()
I was south west of that around Northborough, Marlborough. I spent a lot of time around your area in Salisbury beach though. Back in the late 70's early 80's it was a great amusement area.
|
#10
|
||||
|
||||
![]()
I was riding today....
Very fun. Actually the Yerf did WAYYYY better than the oddyssey..... ![]() I wanted a few more pics, but my phone battery died right after I took this one. Look at all the snow covering it, and the snow free drivers seat. Donuts, 180's, sliding side ways, rooster tails, figure 8's, what a hoot!!!!
__________________
My Yerban assault vehicle: 2.2mm stroker crank, 62mm Nikasil cyl, Taida large vavle head, American made valve springs, ported intake manifold, TM 28mm carb, stock CDI, Bando coil, TK exhaust, stock CVT except for the 14g sliders, 13/40 internal gears, 16T drive, 31T axle sprocket, 22" rear tires, and ONE BIG POTATO CANNON mounted on top.......... |
#11
|
||||
|
||||
![]() Quote:
__________________
Hammer head Single seater know as herbie under construction Aluminum fuel tank, aluminum wheels, custom fuel/cargo rack, entire rewire, trail tech vapor, ported big valve head, a12camshaft, 12 gram sliders, straight intake, kirkey wide seat, front end extension. 4 point harness, welded cage. Hammerhead exhaust. Blade Single Seater Restore welded cage, engine build, new wiring harness/electric box, spun aluminum fuel tank. |
#12
|
||||
|
||||
![]() Quote:
![]()
__________________
Hammer head Single seater know as herbie under construction Aluminum fuel tank, aluminum wheels, custom fuel/cargo rack, entire rewire, trail tech vapor, ported big valve head, a12camshaft, 12 gram sliders, straight intake, kirkey wide seat, front end extension. 4 point harness, welded cage. Hammerhead exhaust. Blade Single Seater Restore welded cage, engine build, new wiring harness/electric box, spun aluminum fuel tank. |
#13
|
||||
|
||||
![]()
Yeah, I was giggling like a kid.....
__________________
My Yerban assault vehicle: 2.2mm stroker crank, 62mm Nikasil cyl, Taida large vavle head, American made valve springs, ported intake manifold, TM 28mm carb, stock CDI, Bando coil, TK exhaust, stock CVT except for the 14g sliders, 13/40 internal gears, 16T drive, 31T axle sprocket, 22" rear tires, and ONE BIG POTATO CANNON mounted on top.......... |
#14
|
|||
|
|||
![]()
I miss the snow but I don't miss the cold.
|
![]() |
|
|