BuggyMasters.Com - An On Line Mini Buggy Forum and Go Kart Forum

Go Back   BuggyMasters.Com - An On Line Mini Buggy Forum and Go Kart Forum > Technical Discussions > Go Kart Engine and Torque Converter Tech

Go Kart Engine and Torque Converter Tech Forum for discussing go kart engines and torque converters (Briggs, Tecumseh, Suburu, Comet etc)

 
 
Thread Tools
  #1  
Old 03-23-2016, 09:30 PM
ModdedMotor212 ModdedMotor212 is offline
Lite Contributor
 

Join Date: Mar 2016
Posts: 84
Default Valve Springs: does acceleration increase?

I was wondering if the stock springs are replaced with heavier ones Does acceleration increase ?

I'm guessing if there is a good air/fuel mix with a good spark plug then acceleration will increase.
I mean it isn't like we are turning it by hand besides to start it.

i'm asking because when i give my engine a little over half throttle no more RPM is gained. i just don't want to lose any torque that can't be fixed with more throttle if that makes sense.

Or should i just get a different ratio rocker arms?
  #2  
Old 03-24-2016, 09:36 AM
SYCARMS's Avatar
SYCARMS SYCARMS is offline
Supporting Vendor
 

Join Date: Sep 2009
Location: Senatobia, Mississippi
Posts: 3,375
Default

Springs do not increase acceleration. A stock spring is made to function within a certain perimeter. A stock spring for instance will work proficiently within a certain rpm range. When increasing the power band to higher rpm's the stock springs could cause valve float, or running a cam with an excessive lift can cause valve bind. One must be careful when choosing the correct valve spring for if too weak valves will eventually float causing the piston to contact the valve whereas if too strong the valves will beat themselves into the seats.
  #3  
Old 04-06-2016, 07:53 PM
ModdedMotor212 ModdedMotor212 is offline
Lite Contributor
 

Join Date: Mar 2016
Posts: 84
Default

The other half of my question would be.. Do stiffer valve springs DECREASE acceleration?
  #4  
Old 04-07-2016, 09:22 AM
SYCARMS's Avatar
SYCARMS SYCARMS is offline
Supporting Vendor
 

Join Date: Sep 2009
Location: Senatobia, Mississippi
Posts: 3,375
Default

Reread my previous post. The stock valve spring is designed to work with a cam up to certain cam specs ( lift& duration). Once you move outside the stock perimeters of the cam you must upgrade the springs to match the new cam spec. It amazes me when I read on a site that the spring they were selling would help increase performance. The spring alone will not help performance unless matched with the cam. Kinda like if your shoe size is a 10. If you buy a size 12 or 9 you will have problems.

Last edited by SYCARMS; 04-07-2016 at 09:35 AM.
  #5  
Old 04-24-2016, 12:43 AM
ModdedMotor212 ModdedMotor212 is offline
Lite Contributor
 

Join Date: Mar 2016
Posts: 84
Default

For a straight answer , i will answer my self.
Answer: The 18 pound springs don't hinder acceleration.
  #6  
Old 04-25-2016, 04:59 PM
scjeep4.7HO scjeep4.7HO is offline
Contributor
 

Join Date: Apr 2015
Location: Virginia
Posts: 197
Default

Lighter (not cheaper) may free up some HP in larger displacement engines. It wouldn't do anything noticeable to a 150cc. It can help a built engine perform at its maximum but the spring itself really adds negligible HP.
  #7  
Old 04-27-2016, 12:42 PM
mtbdudex's Avatar
mtbdudex mtbdudex is offline
Contributor
 

Join Date: Nov 2015
Location: SE Michigan
Posts: 136
Default

Back in the 1970's when I built engines (ha, Ford 390 FE big block, 427 Med riser heads dual quads, etc in my 1969 Torino GT fastback), they used to have a graph of different combinations of cams/valve springs and the rpm range they worked thru ... handy thing to have ... I'm sure those exist for todays gearheads also right?

scanned polaroid 1979 my dads garage in Warren Michigan, I was 17 and knew "everything" ....
I did everything myself, just had a basic Ford service manual, oh and 3 doors down the "Murray brothers" who raced locally.
__________________
Mike R, P.E.
2015 150cc TAOTAO Targa 150
  #8  
Old 04-27-2016, 01:46 PM
mtbdudex's Avatar
mtbdudex mtbdudex is offline
Contributor
 

Join Date: Nov 2015
Location: SE Michigan
Posts: 136
Default

Here, OP read this link to educate yourself
http://garage.grumpysperformance.com...lve-train.181/
__________________
Mike R, P.E.
2015 150cc TAOTAO Targa 150
  #9  
Old 04-28-2016, 07:20 AM
ModdedMotor212 ModdedMotor212 is offline
Lite Contributor
 

Join Date: Mar 2016
Posts: 84
Thumbs up

Quote:
Originally Posted by mtbdudex View Post
Here, OP read this link to educate yourself
http://garage.grumpysperformance.com...lve-train.181/
Thanks, i really do appreciate this. I'm reading through it now.

edit: most of it i don't need to know yet but thanks for the info. and wow i bet your Torino was a monster with dual quad carbs with a 390 combo.

Last edited by ModdedMotor212; 04-28-2016 at 07:55 AM.
  #10  
Old 04-29-2016, 01:12 PM
mtbdudex's Avatar
mtbdudex mtbdudex is offline
Contributor
 

Join Date: Nov 2015
Location: SE Michigan
Posts: 136
Default

Why am I alive today? ...
The good lord wanted me to get past my crazy stage, get married and have kids of my own, that's the only way I can say it.
Having that much hp (true 450) in a car weighing less than 3200 lbs with a 4.11 rear end is not responsible for a 17/18 year old.

Back to cams/valve springs.... fun stuff, though for now on my basic 150cc go kart I'll keep it stock except minor stuff. My boys ages 10/12 it's enough for them now.

Good luck on your journey.
__________________
Mike R, P.E.
2015 150cc TAOTAO Targa 150
 


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:32 AM.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.