|
FrankenBuggy Tech Unconventional and Home Built Buggy Tech Forum |
|
Thread Tools |
#1
|
||||
|
||||
What do you think about using a Baja Reaction 150 as a Frankenbuggy
I can get a pretty clean Baja Reaction 150 for $400. The only downside is that it smokes. However, i'm not to concerned about the engine, because I have an atc 200 engine waiting for a new home. Any concerns, problem areas to watch out for?
__________________
2005 Hammerhead 150 170cc BBK, PnP Big valve Head, A12 Cam, Uni Filter, Custom Exhaust, 10G rollers, 1500 Contra Spring, 2000 Clutch Springs Just added - 2007 Joyner 250 SV - Let the fun begin 4-Dirt Bikes, Baja Bug and enough toys to keep me in the garage and out of trouble. |
#2
|
||||
|
||||
I have one; (the wife's) Not too bad of a base to work with. Front end lower a-arms could be pulled out from where they mount inside of the cage for a long arm/long travel setup. Primary roll protection should be beefed up and welded in place. the one i had was rolled, the side bolt-in vertical bar is bent back. out back it's the typical swingarm, very similar to the spiderbox design and prone to the same issues of bending down around the tensioner and cracking in about the same places. The seats/harnesses just plain bite--typical sloppy junk harnesses and thinly padded seats.
|
#3
|
||||
|
||||
Have you seen or have a link to anyone that has done the front end upgrade?
__________________
2005 Hammerhead 150 170cc BBK, PnP Big valve Head, A12 Cam, Uni Filter, Custom Exhaust, 10G rollers, 1500 Contra Spring, 2000 Clutch Springs Just added - 2007 Joyner 250 SV - Let the fun begin 4-Dirt Bikes, Baja Bug and enough toys to keep me in the garage and out of trouble. |
#4
|
||||
|
||||
there may be one or two that were modded on buggynews. first thing i thought about doing when i looked at it (even before i bought it). Just bothers me when they stick a-arms way inboard or deep in on the underside of the floorpan where there will be interference preventing a pretty simple shock and rack adjustment to extend the droop for greater travel and clearance.
Last edited by x-bird; 05-23-2013 at 09:48 PM. |
#5
|
||||
|
||||
I haven't pulled the trigger yet, but the frame in between the a arms is a stroke of engineering genius, or just maybe someone having a stroke. I believe that I have some ideas for a work around, but if I start the build I will share all info.
__________________
2005 Hammerhead 150 170cc BBK, PnP Big valve Head, A12 Cam, Uni Filter, Custom Exhaust, 10G rollers, 1500 Contra Spring, 2000 Clutch Springs Just added - 2007 Joyner 250 SV - Let the fun begin 4-Dirt Bikes, Baja Bug and enough toys to keep me in the garage and out of trouble. |
#6
|
|||
|
|||
I have a Reaction with an Arctic Cat 454 quad engine in it. The frame is plenty strong but the front suspension is lacking.
|
#7
|
||||
|
||||
I decided not to pull the trigger on the reaction. Just too many small issues that could add up to big $. Its hard not letting your emotions rule your buying tendencies, but I was able to walk away from a good deal and continue the search for a great deal. A Baja Dune just pop upped on CL and I hope to take a look at it today. It looks like the Dune has better front suspension then the Reaction.
__________________
2005 Hammerhead 150 170cc BBK, PnP Big valve Head, A12 Cam, Uni Filter, Custom Exhaust, 10G rollers, 1500 Contra Spring, 2000 Clutch Springs Just added - 2007 Joyner 250 SV - Let the fun begin 4-Dirt Bikes, Baja Bug and enough toys to keep me in the garage and out of trouble. |
#8
|
||||
|
||||
Quote:
|
#9
|
||||
|
||||
Well I missed out on the dune. I was the second caller on it and the seller said that he had someone coming to look at it and he would call me back. By the time I got the trailer hooked up, the phone rang and
So now I am back looking again
__________________
2005 Hammerhead 150 170cc BBK, PnP Big valve Head, A12 Cam, Uni Filter, Custom Exhaust, 10G rollers, 1500 Contra Spring, 2000 Clutch Springs Just added - 2007 Joyner 250 SV - Let the fun begin 4-Dirt Bikes, Baja Bug and enough toys to keep me in the garage and out of trouble. |
#10
|
||||
|
||||
Just be patient, it took me 9 months, but well worth it!!!
|
#11
|
||||
|
||||
The that bought the dune, just washed it and turned around and put it on CL for $1000. I could tell it was the same one by the stickers.
__________________
2005 Hammerhead 150 170cc BBK, PnP Big valve Head, A12 Cam, Uni Filter, Custom Exhaust, 10G rollers, 1500 Contra Spring, 2000 Clutch Springs Just added - 2007 Joyner 250 SV - Let the fun begin 4-Dirt Bikes, Baja Bug and enough toys to keep me in the garage and out of trouble. |
#12
|
||||
|
||||
I hear ya, there are always sharks in the water!
|
|
|