|
|
|
#1
09-16-2010, 02:39 PM
|
||||
|
||||
Lost GY6 ?
Bought a buggy with a gy6 that supposedly needed a coil and that was it,,,,,,, so after new coil,regulator,cdi box and engine wiring harness it will now fire but wont do more than idle soon as i hit the throttle easy or hard it dies, still has spark ,I believe it is fuel related although i've cleaned the carb 3 times,flushed the fuel tank am getting fuel to the carb any help would be great
|
|
#2
09-16-2010, 03:50 PM
|
||||
|
||||
|
check your float level-set your valves welcome to the group
__________________
olderthan 2008 tomberline punisher 1500 spring 12g sliders 30mm cv pumper carb uni filter no rev cdi polaris xlt snowmobile shocks for front w/550 magnum springs & blaster fronts on rear and another buggy built working on mods gk-13 white spring 17 gram sliders so far |
|
#3
09-16-2010, 10:02 PM
|
||||
|
||||
|
Quote:
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE! |
|
#4
09-16-2010, 10:56 PM
|
||||
|
||||
|
joshstep1 huh?
__________________
olderthan 2008 tomberline punisher 1500 spring 12g sliders 30mm cv pumper carb uni filter no rev cdi polaris xlt snowmobile shocks for front w/550 magnum springs & blaster fronts on rear and another buggy built working on mods gk-13 white spring 17 gram sliders so far |
|
#5
09-16-2010, 10:58 PM
|
||||
|
||||
|
If you look into the carb where the air intake is, there's a black thing that hangs down
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE! |
|
#6
09-16-2010, 11:10 PM
|
||||
|
||||
|
are you talking about the slide
__________________
olderthan 2008 tomberline punisher 1500 spring 12g sliders 30mm cv pumper carb uni filter no rev cdi polaris xlt snowmobile shocks for front w/550 magnum springs & blaster fronts on rear and another buggy built working on mods gk-13 white spring 17 gram sliders so far |
|
#7
09-16-2010, 11:11 PM
|
||||
|
||||
|
Yeah... I guess
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE! |
|
#8
09-16-2010, 11:15 PM
|
||||
|
||||
|
i was confused because they are alum. colored silver esh
__________________
olderthan 2008 tomberline punisher 1500 spring 12g sliders 30mm cv pumper carb uni filter no rev cdi polaris xlt snowmobile shocks for front w/550 magnum springs & blaster fronts on rear and another buggy built working on mods gk-13 white spring 17 gram sliders so far |
|
#9
09-16-2010, 11:16 PM
|
||||
|
||||
|
how are you coming on the new buggy
__________________
olderthan 2008 tomberline punisher 1500 spring 12g sliders 30mm cv pumper carb uni filter no rev cdi polaris xlt snowmobile shocks for front w/550 magnum springs & blaster fronts on rear and another buggy built working on mods gk-13 white spring 17 gram sliders so far |
|
#10
09-17-2010, 10:21 AM
|
||||
|
||||
|
I adjusted the valves last night and was able to get it running....not right but running...if I feather the gas it will start at high idler (runs great from high idle to full throttle) and able to run it wide open, it's a lot peppier than I thought it would be, but when i come to a stop the clutch is still pulling so when I turn the idle down it bogs out and dies ?
|
|
#13
09-17-2010, 01:26 PM
|
||||
|
||||
|
post more pics of your buggy
you may have a choke problem-if they don't shut off they can cause high idle pull it measure lenght of the little brass thingy hook to battery for 5 min should get about 1/4 longer. where the 2 bolts on the housing for carb goes is a small hole into the carb clean it also
__________________
olderthan 2008 tomberline punisher 1500 spring 12g sliders 30mm cv pumper carb uni filter no rev cdi polaris xlt snowmobile shocks for front w/550 magnum springs & blaster fronts on rear and another buggy built working on mods gk-13 white spring 17 gram sliders so far |
|
#14
09-18-2010, 12:00 AM
|
||||
|
||||
|
Quote:
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE! |
|
|
