|
|
|
|||||||
| Mini Buggy General Discussion General Discussion forum for Mini Buggies. (American Sportworks, HammerHead, Carter, etc) |
|
|
Thread Tools |
|
#1
10-30-2013, 09:37 AM
|
|||
|
|||
Big Thanks to...
miamieddie, x-bird, mastertoyota, sycarms, zman, for putting up with my noob bearing questions. I appreciate the help and advise..
__________________
2013 Trailmaster XRX 150 Type 86 stroker Taida 4V head with 23/22mm valves, forged 4V piston,Taida 62mm jug,forged Taida 8200 KDU stroker crank, Koso high-flow oil pump, Taida case half w/ oil cooler ports, Setrab oil cooler,TrailTec Vapor, Mikuni VM26-606, aluminum 30mm intake, Uni filter, aluminum stack, Hammerhead racing exhaust, MotoRio adjustable CDI/HO Coil, Iridium plug, Full Dr Pulley CVT kit w/ 16g sliders, JD's Mikuni slide kit 2014 Kandi 90B |
|
#2
10-30-2013, 10:34 AM
|
||||
|
||||
fixed?
__________________
ASE Master and Toyota Master Diagnostic Certified Buggy Building Trainee '04 Dazon Raider 150 'modded' |
|
#3
10-30-2013, 10:55 AM
|
|||
|
|||
|
Yup, that bearing was SMOKED. It looked like it heated up quite a bit, because the inside of the dustshields looked like they were stating to melt, or chewed up by something, even the inside of the housing looked a little banged up, might order a spare set of those..slide hammer got the housing off cleaned it up threw it in the oven, bearings in the freezer, and they dropped right in.. Gonna try to get everything put back together tonight, but no rush because the US Army ownes my ass this weekend.
__________________
2013 Trailmaster XRX 150 Type 86 stroker Taida 4V head with 23/22mm valves, forged 4V piston,Taida 62mm jug,forged Taida 8200 KDU stroker crank, Koso high-flow oil pump, Taida case half w/ oil cooler ports, Setrab oil cooler,TrailTec Vapor, Mikuni VM26-606, aluminum 30mm intake, Uni filter, aluminum stack, Hammerhead racing exhaust, MotoRio adjustable CDI/HO Coil, Iridium plug, Full Dr Pulley CVT kit w/ 16g sliders, JD's Mikuni slide kit 2014 Kandi 90B |
|
#4
10-30-2013, 11:27 AM
|
||||
|
||||
|
I think I can speak for all of us here, good to hear you got it figured out, and thanks for your service.
__________________
ASE Master and Toyota Master Diagnostic Certified Buggy Building Trainee '04 Dazon Raider 150 'modded' |
|
#6
10-30-2013, 07:42 PM
|
||||
|
||||
|
you"re welcome and also thanks for your service too.
|
|
#7
10-30-2013, 09:23 PM
|
|||
|
|||
|
back together and rolling smooooooooooth.
__________________
2013 Trailmaster XRX 150 Type 86 stroker Taida 4V head with 23/22mm valves, forged 4V piston,Taida 62mm jug,forged Taida 8200 KDU stroker crank, Koso high-flow oil pump, Taida case half w/ oil cooler ports, Setrab oil cooler,TrailTec Vapor, Mikuni VM26-606, aluminum 30mm intake, Uni filter, aluminum stack, Hammerhead racing exhaust, MotoRio adjustable CDI/HO Coil, Iridium plug, Full Dr Pulley CVT kit w/ 16g sliders, JD's Mikuni slide kit 2014 Kandi 90B |
|
|
