|
|
|
|||||||
| 250cc and Above Engine Tech Technical Discussion Forum for 250cc and up Engines |
|
|
Thread Tools |
|
#1
02-21-2012, 12:24 PM
|
|||
|
|||
perfomace mods
im just wondering what kind of performace mods has anyone made to there buggy. im just also looking for ideas for mine. i have a duece dingo with a 12 hp motor.
|
|
#2
02-21-2012, 06:19 PM
|
||||
|
||||
|
Don't think you have the same engine as me (GY6 150cc), but here's some idea for you.
Post #11 http://buggymasters.com/forum/showthread.php?t=2670 |
|
#3
02-21-2012, 07:07 PM
|
|||
|
|||
|
thanks for the ideas. the only thing is mine is only belt run.
|
|
#4
02-21-2012, 07:11 PM
|
|||
|
|||
|
the mods i have right now are e3 sparkplug( i have a small sponsorship from them) royal purple moter oil. a k and n air filter with mods that come with it.
|
|
#5
02-21-2012, 11:40 PM
|
||||
|
||||
|
So does it have a Torque A verter? (TAV for short)
How about port matching the carb to intake manifold and intake manifold to head? Maybe have the head ported? What kind of exhaust is on that engine? |
|
#6
02-23-2012, 03:33 PM
|
|||
|
|||
|
how can i get my head ported. and i have stock exhaust. how do i port matching the carb to intake manifold and intake manifold to head?
|
|
#8
02-29-2012, 12:22 PM
|
|||
|
|||
|
i need just to find a k and n filter replacement now does anyone know where i can find one?
|
|
#9
02-29-2012, 06:42 PM
|
||||
|
||||
|
|
|
#10
03-02-2012, 09:21 AM
|
|||
|
|||
|
did that didnt get me anywhere.
|
|
#12
03-02-2012, 07:54 PM
|
|||
|
|||
|
i went down to every model they dont even have one close to it. i even went in to the lawn and garden part nothing.
|
|
#13
03-02-2012, 11:34 PM
|
||||
|
||||
|
for port matching, you need to remove the carb and intake pipe, and take note of the gasket on the one side and its imprint on the other. carefully mark (use a sharpie etc.) any metal on the face of the mating surface inside the gasket opening and remove the gasket. Grind away just the marked metal in a nice smooth transition to the rest of the port. Dremel with a roll sander, die grinder etc. Doing that to both pieces removes any obstructions from misalignment of the two pieces (the openings now match--hence the term gasket and or port matching) and also opens up the area in terms of volume. If the pieces have some movement on the studs or bolts when loosened--most do-- make "witness" marks on the outside surface prior to disassembly so you can put them back together in the exact same location so the openings are spot on.
Last edited by x-bird; 03-02-2012 at 11:36 PM. |
|
#14
03-03-2012, 09:34 AM
|
||||
|
||||
|
Quote:
Quote:
You HAVE a K&N air filter, but you can't FIND the K&N filter on their site? Is that what you're asking???? 
|
|
#15
03-03-2012, 11:38 AM
|
|||
|
|||
|
yea i guess they dont make them for that anymore
|
|
#17
03-04-2012, 06:49 AM
|
||||
|
||||
|
you may take a K&N that is listed for another application other than yours. Try looking for the filter using diminsions (size of inlet, length diameter , etc.) rather than searching for your particular model.
|
|
#18
03-12-2012, 09:48 AM
|
|||
|
|||
|
i looked at it. k and n say k and n on top its a knock off thats for telling me.
|
|
|
