![]() |
![]() |
|
150cc GY6 and Under Engine Tech GY6 and Smaller Technical Discussion Forum |
![]() |
|
Thread Tools |
#1
|
|||
|
|||
![]()
Havent been on here in years due to some stuff, but finally threw a new engine in my TM XRS150. Finally got it cranked but seem to be having idling issues after I run it for a bit and idles high. If I stomp the gas it bogs down while driving. I'm curious what jets I should be running with a ported polished shaved syc big valve head, hammerhead exhaust and r2c filter. I'm at 778' above sea level. Near the Chattanooga area. Like to get it up and running so I can sell both the 150 and hammerhead 250.
__________________
Trailmaster XRX 150 ![]() TK Variator and 1500 Spring ![]() SYC Performance Ported & Polished & Shaved 2 Valve Head, A-10 Camshaft, R2C Filter, and Hammerhead Exhaust ![]() Hammerhead 250GTS White Torque and Clutch Springs, 18g Rollers, R2C Filter, Ported Polished and Shaved Head, Hammerhead Exhaust |
#2
|
||||
|
||||
![]()
How does the plug look?
|
#3
|
|||
|
|||
![]()
The plug is black, but only because its old. I cant get a wot run to check the plug. But curious what you would recommend jetting at with my setup. You usually are pretty spot on when it comes to jet recommendations. I'm looking for a good starting point. 130 main and 38 pilot aren't cutting it.
__________________
Trailmaster XRX 150 ![]() TK Variator and 1500 Spring ![]() SYC Performance Ported & Polished & Shaved 2 Valve Head, A-10 Camshaft, R2C Filter, and Hammerhead Exhaust ![]() Hammerhead 250GTS White Torque and Clutch Springs, 18g Rollers, R2C Filter, Ported Polished and Shaved Head, Hammerhead Exhaust |
#4
|
||||
|
||||
![]()
Make sure your choke is closing off. Make sure you have power to it. Aren't you using the same cam,head and exhaust? If so it should not change that much to effect performance.
|
#5
|
|||
|
|||
![]()
I have the manual choke, so I dont believe that is the issue. Yeah, Im still using the same stuff just transplanted in a new engine. Im guessing by lowering the jet to the 130 and it bogging down completely without even getting to half throttle this time, that would indicate not enough fuel?
__________________
Trailmaster XRX 150 ![]() TK Variator and 1500 Spring ![]() SYC Performance Ported & Polished & Shaved 2 Valve Head, A-10 Camshaft, R2C Filter, and Hammerhead Exhaust ![]() Hammerhead 250GTS White Torque and Clutch Springs, 18g Rollers, R2C Filter, Ported Polished and Shaved Head, Hammerhead Exhaust |
#6
|
||||
|
||||
![]()
You could also have a vacuum leak causing this issue.
__________________
2010 Carter Interceptor GTR 300 2010 Hammerhead 250 SS 2015 Kandi 49FM5 110cc 2015 Hammerhead GTS 250-SOLD 2008 Kazuma Coyote 150-SOLD |
#7
|
|||
|
|||
![]()
Well I tried different jets with the same outcome, so I don't believe its a jet issue. Sprayed around the intake with no issues of leaks. Took the top off to look at the camshaft and it seems to be lined up properly. Need to find my feeler gauge and check valve clearance. Could that be the issue? If the camshaft was off 1 tooth could that cause this problem?
One other thing, I originally installed an 11pole stator, rectifier, and the add on harness, but switched back to the stock stuff when I couldn't get it started. I believe one of the wires on one of the plugs had to be moved when doing that upgrade. Maybe Tom knows which one I am referring to. I cant recall if it is on the 11 pole harness or the factory harness, maybe this could be the culprit?
__________________
Trailmaster XRX 150 ![]() TK Variator and 1500 Spring ![]() SYC Performance Ported & Polished & Shaved 2 Valve Head, A-10 Camshaft, R2C Filter, and Hammerhead Exhaust ![]() Hammerhead 250GTS White Torque and Clutch Springs, 18g Rollers, R2C Filter, Ported Polished and Shaved Head, Hammerhead Exhaust |
#8
|
||||
|
||||
![]()
One tooth off could negatively effect performance depending if it is retarded but it will not do what you described. It would have to be way off or if valve adjustment is holding valves open.
|
#9
|
|||
|
|||
![]()
Another thing I have noticed through all of this. Is once the engine gets warmer the bogging happens much quicker. It also seems to stall out when idling the warmer it gets.
__________________
Trailmaster XRX 150 ![]() TK Variator and 1500 Spring ![]() SYC Performance Ported & Polished & Shaved 2 Valve Head, A-10 Camshaft, R2C Filter, and Hammerhead Exhaust ![]() Hammerhead 250GTS White Torque and Clutch Springs, 18g Rollers, R2C Filter, Ported Polished and Shaved Head, Hammerhead Exhaust |
#10
|
||||
|
||||
![]()
Is the choke working?
|
![]() |
|
|