BuggyMasters.Com - An On Line Mini Buggy Forum and Go Kart Forum

Go Back   BuggyMasters.Com - An On Line Mini Buggy Forum and Go Kart Forum > Site News and Suggestions > New Member Introduction

New Member Introduction New to the forum? Say hello here!

 
 
Thread Tools
  #1  
Old 10-02-2017, 06:40 PM
Sammyjo0512 Sammyjo0512 is offline
Lurker
 

Join Date: Sep 2017
Location: Georgia
Posts: 18
Default Yerf dog gx150

Hello all new to buggy masters! I have a yerf dog gx150 I think it's a 2005 model and I bough it about 8months ago and the last guy said he bought the whole even 3rd generation front end for it from bmi with the buggy Depot hd ball joints. My problem is that the camber on the tires is way inwards and nothing is bent or broken but is still bent in wards I bought the hd top a arms from bd and the bottoms too all third gen but still didn't correct the problem I don't know what to do because it just eats through tires and I'm tired of spending tons of money on tires. I'm thinking the ball joints may be worn out but also the top a arm tabs may be short by a 1/4 or 1/2 inch. What can I do?
  #2  
Old 10-02-2017, 08:21 PM
Sammyjo0512 Sammyjo0512 is offline
Lurker
 

Join Date: Sep 2017
Location: Georgia
Posts: 18
Default

I don't want to spend 100$ on ball joints just to figure out my top a a arms were short by 1/2 inch
  #3  
Old 10-02-2017, 09:26 PM
xlint89's Avatar
xlint89 xlint89 is offline
Senior Member
 

Join Date: Dec 2011
Location: cleveland OH
Posts: 1,064
Default

Welcome to the site.

Clear pictures can tell us a lot more than your description.
__________________
My Yerban assault vehicle: 2.2mm stroker crank, 62mm Nikasil cyl, Taida large vavle head, American made valve springs, ported intake manifold, TM 28mm carb, stock CDI, Bando coil, TK exhaust, stock CVT except for the 14g sliders, 13/40 internal gears, 16T drive, 31T axle sprocket, 22" rear tires, and ONE BIG POTATO CANNON mounted on top..........
  #4  
Old 10-03-2017, 06:40 AM
Sammyjo0512 Sammyjo0512 is offline
Lurker
 

Join Date: Sep 2017
Location: Georgia
Posts: 18
Default

Here you are I didn't get to do the other side I had to leave for work.
Attached Images
File Type: jpg IMG_4191.jpg (88.4 KB, 23 views)
File Type: jpg IMG_4190.jpg (93.7 KB, 18 views)
  #5  
Old 10-03-2017, 06:42 AM
Sammyjo0512 Sammyjo0512 is offline
Lurker
 

Join Date: Sep 2017
Location: Georgia
Posts: 18
Default

But when I take my top and bottom a arms off they are the same size. It it a possibility the a arm tabs were welded on at the wrong level?
  #6  
Old 10-03-2017, 08:25 AM
OLDKID's Avatar
OLDKID OLDKID is offline
Contributor
 

Join Date: Nov 2014
Location: Western N.Y.
Posts: 457
Cool

That bottom ball joint is way out of line , normally both studs are vertical in unison . Pull it off and see if its all wobbly . When new they're real tight .
__________________
2011 BMS KING COBRA 150 Sold
YERF DOG SPIDERBOX's Sold
YERF DOG 3203's. Sold
MANCO SILVER FOX. Sold
2009 POLARIS 500 HO SPORTSMAN 4X4
2002 POLARIS 500 HO SPORTSMAN 4X4
2000 POLARIS MAGNUM 2X4
HALF A DOZEN CHEVY 4X4's
NEED-MO-BUGGY
  #7  
Old 10-03-2017, 08:29 AM
OLDKID's Avatar
OLDKID OLDKID is offline
Contributor
 

Join Date: Nov 2014
Location: Western N.Y.
Posts: 457
Default

PS - they're life time warranty .
__________________
2011 BMS KING COBRA 150 Sold
YERF DOG SPIDERBOX's Sold
YERF DOG 3203's. Sold
MANCO SILVER FOX. Sold
2009 POLARIS 500 HO SPORTSMAN 4X4
2002 POLARIS 500 HO SPORTSMAN 4X4
2000 POLARIS MAGNUM 2X4
HALF A DOZEN CHEVY 4X4's
NEED-MO-BUGGY
  #8  
Old 10-03-2017, 08:36 AM
tkeagle tkeagle is offline
Heavy Contributor
 

Join Date: Mar 2015
Location: Central Kansas
Posts: 556
Default

I had same issue. With the beefed up a arms, there is barley enough room for nuts on the ball joints to go all way down. Check to see if on the bottom side of ball joints are tight. They tend to get slack in them. If so, the ball joint will push out. Check all points of ball joints. Should be able to just push on tire, and if looks like there is slack on spindles, need tighten. Use (lock tite) on the nuts of ball joints. Also, check your large nuts, that connect your a arms to bulk head. They tend to vibrate loss also. But not noticeable. Again, should be no slack in them. If none of that fix it, contact Travis at BD. He might have a better fix. Or might know what's going on.
I still have a slight inward on my passenger side also. Very slight. Not big issue. Not near as much as what you got. But if he has answer, let me know. .
Also, check you bulk head. Make sure it's mounted straight on frame. Can check your shocks also. If there is any kind of length adjustment. The nut can come loss. And change length on shock. Somehow, happened to me as well. Even though both ends are locked in place, the shaft, can freely spin, and turn it self out. Might need to take both shocks completely out, and compare.
Lock tite. .

Last edited by tkeagle; 10-03-2017 at 08:38 AM.
  #9  
Old 10-03-2017, 09:26 AM
Sammyjo0512 Sammyjo0512 is offline
Lurker
 

Join Date: Sep 2017
Location: Georgia
Posts: 18
Default

So when the ball joints are off should I be able to move them around very freely at the joint or should it be staying straight with a little bit of movement? And the lifetime warranty says it doesn't cover against eventual wear which is what I thought it was
  #10  
Old 10-03-2017, 12:15 PM
Sammyjo0512 Sammyjo0512 is offline
Lurker
 

Join Date: Sep 2017
Location: Georgia
Posts: 18
Default

Travis @ bd said that the ball joints wouldn't cause this worn out or not
  #11  
Old 10-03-2017, 01:02 PM
tkeagle tkeagle is offline
Heavy Contributor
 

Join Date: Mar 2015
Location: Central Kansas
Posts: 556
Default

Yes, when off, they should move freely.
  #12  
Old 10-03-2017, 01:06 PM
tkeagle tkeagle is offline
Heavy Contributor
 

Join Date: Mar 2015
Location: Central Kansas
Posts: 556
Default

There is a mark on each ball joint. A "C" I think. That mark needs to be facing inwards towards buggy.... I think... Might be so ball joint stays in. Looks the top ball joint is pushing out. Don't think that is right.
  #13  
Old 10-03-2017, 01:14 PM
Sammyjo0512 Sammyjo0512 is offline
Lurker
 

Join Date: Sep 2017
Location: Georgia
Posts: 18
Default

All right thanks I'll take a look when I get home
  #14  
Old 10-03-2017, 01:19 PM
Sammyjo0512 Sammyjo0512 is offline
Lurker
 

Join Date: Sep 2017
Location: Georgia
Posts: 18
Default

I posted on the bd forum too like Travis said to do and he said the ball joints aren't worn out I don't understand or know what else it could be if nothing is bent. My shocks are all good does anyone know how long the even top a arms are from the end of the tab to end of the pipe?
  #15  
Old 10-04-2017, 07:41 AM
T@BD's Avatar
T@BD T@BD is offline
Supporting Vendor
 

Join Date: Nov 2015
Posts: 50
Default

I'm handling this over on the BD forum, but wanted to clarify here as well.

With correct installation, there isn't any way possible that my joints can cause such a severe camber problem, even if worn. It would be easy to send out a new set of ball joints, but that's not the problem. The issue is going to be either the A-Arms, or the spindles.

Also, my joints don't loosen on their own, and you don't need to tighten them periodically. If yours are loosening, either the threads are damaged or they aren't being tightened to spec.

However, the first problem I see is that the ball joints aren't installed. I couldn't see this until I brightened and enlarged the picture.

Attached Images
File Type: jpg file3.jpg (91.8 KB, 25 views)
__________________
Travis @ Buggy Depot

  #16  
Old 10-04-2017, 08:24 AM
Sammyjo0512 Sammyjo0512 is offline
Lurker
 

Join Date: Sep 2017
Location: Georgia
Posts: 18
Default

Thank you for handling this Travis sorry for all the problems
  #17  
Old 06-19-2018, 07:53 AM
Sammyjo0512 Sammyjo0512 is offline
Lurker
 

Join Date: Sep 2017
Location: Georgia
Posts: 18
Default

How do I start a new thread I forgot how to do it?
  #18  
Old 06-19-2018, 09:06 AM
neo71665 neo71665 is offline
Contributor
 

Join Date: Jun 2017
Posts: 284
Default

Quote:
Originally Posted by Sammyjo0512 View Post
How do I start a new thread I forgot how to do it?
Open correct section and click on the new thread button
 


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:38 PM.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.